Forum Home
Press F1
 
Thread ID: 97070 2009-02-03 07:54:00 Configure VOIP on Dlink DVA-G3340S pico (4752) Press F1
Post ID Timestamp Content User
744551 2009-02-03 07:54:00 Hi all,

I signed up with 2talk (2talk.co.nz) and Snap internet (snap.net.nz) on the naked DSL plan. I got a router which does VOIP but am having some trouble getting it configured. I am connected to the net but I can't configure the VOIP settings. Here is the list of settings I have:


Server Parameters:

Server Address: 2talk.co.nz
Server Port:: 5060
Service Domain: 2talk.co.nz
Outbound Proxy Server: 202.180.76.161
Outbound Proxy Port: 5060
URL Scheme: SIP-URL or TEL-URL
User Parameter: none or phone
Initial Unregister: enable or disable
Register Expires: in sec
Session Expires: in sec
Min-SE: in sec
Session Expires Refresher: uac or uas
Connection: Pvc0
Dial Plan:

User Agent Parameters:

Same Phone Number: enable or disable
Line: 1 or 2
Phone Number: my 2talk phone number
Display Name: my 2talk phone number
User Agent Port: 5060
Authentication Username: my 2talk phone number
Authentication Password: ******
Confirm Password: ******

Telephony Parameters:

Index: 1 or 2
EC: enable or disable
VAD: enable or disable
OOB DTMF: enable(G.711) or disable (RFC2833)
Payload Type:
RX Gain:
TX Gain:
Inter-Digit Timer:

Codec Priority & Packet Interval:
G.711a-law : 1st 2nd 3rd 4th 5th or no use
G.711u-law : 1st 2nd 3rd 4th 5th or no use
G.723.1 : 1st 2nd 3rd 4th 5th or no use
G.729a : 1st 2nd 3rd 4th 5th or no use
G.726 : 1st 2nd 3rd 4th 5th or no use



Does anyone else have this or a similar modem? 		pico (4752)
744552 2009-02-03 08:36:00 what happens when you make a call? Can you receive inbound calls? Chilling_Silence (9)
744553 2009-02-03 09:23:00 Can't make any calls and the website (secure login) says that there are no phones logged in. I don't have settings for some of the parameters. pico (4752)
744554 2009-02-03 10:31:00 So you've plugged in a telephone in to the back of the router?

What parameters are missing? 		Chilling_Silence (9)
744555 2009-02-03 10:34:00 Server Parameters:

Server Address: 2talk . co . nz
Server Port:: 5060
Service Domain: 2talk . co . nz
Outbound Proxy Server: 202 . 180 . 76 . 161
Outbound Proxy Port: 5060
URL Scheme: SIP-URL
User Parameter: phone
Initial Unregister: enable
Register Expires: 600
Session Expires: 600
Min-SE: 600
Session Expires Refresher: uac or uas (Unsure here sorry)
Connection: Pvc0
Dial Plan: (Unsure here either sorry - Defaults?)

User Agent Parameters:

Same Phone Number: enable
Line: 1
Phone Number: my 2talk phone number
Display Name: my 2talk phone number
User Agent Port: 5060
Authentication Username: my 2talk phone number
Authentication Password: ******
Confirm Password: ******

Telephony Parameters:

Index: 1 o
EC: enable (Guessing here)
VAD: enable (Guessing here)
OOB DTMF: disable (RFC2833)
Payload Type:
RX Gain:
TX Gain:
Inter-Digit Timer:

Codec Priority & Packet Interval:
G . 711a-law : 2nd
G . 711u-law : 3rd
G . 723 . 1 : no use
G . 729a : 1st
G . 726 : no use

Try those for starters :) 		Chilling_Silence (9)
744556 2009-02-04 19:56:00 Hi Chill,

Thanks for the suggestions . Turns out that my biggest problem was that I didn't realise I had to reboot the modem for these changes to take effect! Sigh .

I've put my parameters in below for anyone who happens to find this thread . Also so far I haven't been able to get the Telephony settings to commit but it is working at the moment anyway .


Server Parameters:

Server Address: 2talk . co . nz
Server Port:: 5060
Service Domain: 2talk . co . nz
Outbound Proxy Server: 2talk . co . nz
Outbound Proxy Port: 5060
URL Scheme: SIP-URL
User Parameter: phone
Initial Unregister: enable
Register Expires: 600
Session Expires: 600
Min-SE: 600
Session Expires Refresher: uas
Connection: Pvc0
Dial Plan:

User Agent Parameters:

Same Phone Number: enable
Line: 1
Phone Number: my 2talk phone number
Display Name: my 2talk phone number
User Agent Port: 5060
Authentication Username: my 2talk phone number
Authentication Password: ******
Confirm Password: ******

Telephony Parameters:

Index: 1 o
EC: enable
VAD: disable
OOB DTMF: disable (RFC2833)
Payload Type:
RX Gain:
TX Gain:
Inter-Digit Timer:

Codec Priority & Packet Interval:
G . 711a-law : 2nd
G . 711u-law : 3rd
G . 723 . 1 : no use
G . 729a : 1st
G . 726 : no use 		pico (4752)
744557 2009-02-04 21:41:00 Cool, good to hear! :) Chilling_Silence (9)
1