| Forum Home | ||||
| Press F1 | ||||
| Thread ID: 106536 | 2010-01-12 23:13:00 | Installing network jacks on walls. | Nomad (952) | Press F1 |
| Post ID | Timestamp | Content | User | ||
| 848199 | 2010-01-15 03:41:00 | One last question. About that long drill. I take it is not a right angle driller? That means you need to rip a big hole in the wall right? So you can fit the driller inside the walls to drill down. I can always put the jackpoint on top of the wall - don't look pretty thou, if 2 bedroom design. Floor level on one and ceiling level on the other :p |
Nomad (952) | ||
| 848200 | 2010-01-15 03:44:00 | One last question. About that long drill. I take it is not a right angle driller? That means you need to rip a big hole in the wall right? So you can fit the driller inside the walls to drill down. Haha. No. You need to get in the roof and drill down through the top plate of the wall. It's a real bugger if you lose a bit inside the wall! Done that a couple of times :crying Always fun trying to fish it out. :help: |
CYaBro (73) | ||
| 848201 | 2010-01-15 03:46:00 | Haha . No . You need to get in the roof and drill down through the top plate of the wall . It's a real bugger if you lose a bit inside the wall! Done that a couple of times :crying Always fun trying to fish it out . :help: That won't work then . Just above the top bedroom is the window frame :dogeye: Well I could use a side wall . Drill from the top? I need a 6m drill bit then . There is no gap between the floors . Maybe cheaper and easier to rip the gib out :D |
Nomad (952) | ||
| 848202 | 2010-01-15 03:53:00 | Oh I could go under a wardrobe, that works then .... | Nomad (952) | ||
| 848203 | 2010-01-15 04:13:00 | CYaBro what do you mean by terminated properly? | nedkelly (9059) | ||
| 848204 | 2010-01-15 04:14:00 | Yep go what ever way is easiest, dont really want to go knocking holes in walls - just means more work. There has been many time I Have run the ducting along the floor/wall joint, tuck it in tight held on with industrial double sided tape, similar to whats holds trim on some cars. OR as long as the carpet is not stapled down at the edges, but is held by that carpet spikes, it gives you about 25 -30 mm to lift the edge of the carpet, slip it under, then push down the carpet again -- Bingo, hidden cables with only the jack showing at floor level Like These (www.hyperline.com) Really depends also if you want to hide the cables, job I did yesterday -- concrete walls, the guys look ed strange when I asked where i could run ducting :illogical Just drop in the rest that run along the floor --- OK easy then. It's a real bugger if you lose a bit inside the wall! Done that a couple of times OH YEAH -- its :angry followed by -- OH #@%(*&% Only lost one so far. |
wainuitech (129) | ||
| 848205 | 2010-01-15 04:21:00 | CYaBro what do you mean by terminated properly? Prob means wired in the standard sequence - some just dont wire them correctly and its a damn mess, with non connections. either Correct wiring (www.google.co.nz) I usually use 568B | wainuitech (129) | ||
| 848206 | 2010-01-15 04:38:00 | Prob means wired in the standard sequence - some just dont wire them correctly and its a damn mess, with non connections. either Correct wiring (www.google.co.nz) I usually use 568B Yea, just meant that all 8 wires are terminated at both ends as gigabit LAN uses all of them not just 4 like 10/100 does. |
CYaBro (73) | ||
| 848207 | 2010-01-15 05:00:00 | well if that is the case then I am good because I think mine are done like that as well. Pin 1 to 1, 2 to 2, etc | nedkelly (9059) | ||
| 848208 | 2010-01-15 05:00:00 | oh yeah all 8 wires are used | nedkelly (9059) | ||
| 1 2 3 4 | |||||